Track Saw Dust Cover Compatible with Ridgid Saw

The covers are model-specific, so buy the listing that names your saw. We currently make covers for:

• Bosch GKT13 corded track saw
• Dewalt track saw
• Kreg ACS
• Makita SP6000J corded and Makita 36v cordless (separate covers; we do not yet make one for the Makita 40v)
• Milwaukee M18
• Ridgid track saw
• Ryobi track saw
• Wen 6-1/2″ and 7-1/4″ (separate sizes)
• TS 55/TSC 55, TS 60 and TS 75 (separate covers)

If your saw is not on that list, contact us with the exact model number.

No, the covers are model-specific. The Makita 36v cordless cover does not fit the Makita SP6000J corded saw or the Makita 40v saw; the Wen 6-1/2″ and 7-1/4″ saws have different size arbor holes and take different covers; and the TS 55/TSC 55, TS 60 and TS 75 each have their own cover. If you have the corded Makita, order the SP6000J cover.

Yes, and it takes seconds. The cover snaps on by hand with no tools and pulls off the same way, so for a blade change you pull the cover off, swap the blade, and snap it back on.

It covers the open arbor hole on the side of the saw and gives the blade an enclosed housing, which helps the saw’s own dust collection work better. It adds very little to the saw’s side profile. Owners who had been taping over the hole say the cover does the job better than tape, which didn’t last.

Our Miter Bars for Dewalt Table Saw are sized for the Dewalt jobsite table saws. The Set of 4 Adjustable Miter Bars fits the Dewalt jobsite saw too and is listed for Makita and Milwaukee table saws, and we have confirmed it on SawStop, Bosch, Shopsmith and Craftsman table saws, including the Craftsman 137. Both sets are four bars, 225mm long, each with three countersunk screw holes, made of high density plastic so they will not shrink or expand like wood. If your saw is not listed, send us the model number before you order.

The TS 55 guide is designed just for the TS 55 and does not fit the TS 60 or TS 75 track saws; the Kreg ACS guide is a separate product made for that saw. The TS 55 listing is one guide, and one is all you need, but if you want one at the front and one at the back of the saw you will need two. To install, tilt the saw to 45°, slot the guide into the rail and tighten it.

It fits the TSO guide rail square GRS-16 and GRS-16 PE, including the GRS-16 PE v2. It attaches and removes with a thumb screw, and it is acrylic, in black or clear.

No. It does not fit model R4840, which uses triangular knobs, so if your sander has triangular knobs the wrench will not be compatible. On the sanders it fits, the wrench slips over the adjustment knob and gives you the leverage to loosen or tighten it when adjusting belt tension.

Yes. They are made for all 27mm hoses, including the D 27 hose, and the helical coil locks onto the hose so the clips do not slide up and down. Each pack has 10 clips, enough to run the full length of the hose. To install, coil each clip onto the hose and slide the plug-it cable through.

About one minute and a single T10 screw. Our current DF 500 Imperial Thickness Gauge is a direct replacement for the factory metric thickness gauge on the DF 500 and keeps the same positive detent feel as the factory gauge. It gives you seven imperial settings: 1/2″, 5/8″, 3/4″, 7/8″, 1″, 1-1/4″ and 1-1/2″.